收藏本站
SPECIFICATION CONTROL DRAWING
THERMOFIT ASSEMBLY PROCEDURE
SolderSleeve and Lead in
Terminated Assembly
Position for Assembly
INSTALLATION PROCEDURE:
1. Terminals must be tinned prior to placement of sleeves.
2. Cut the correct number of sleeves from the reel.
3. Position sleeves onto connector terminals as shown above and remove tape.
4. Strip wire 4.83 (0.19) and pre-tin.
5. Insert wires into sleeves. Wires should be straight and parallel to terminal.
6. Heating Technique:
a. Infrared Heater IR-1012: Position connector into holding fixture. Place leads to be connected
into correct sleeve. Position heater and energize, after setting timer for correct cycle.
b. Convection Heater CV-4505: Position connector into AD-1327 holding fixture. Place leads to
be connected into correct sleeve. Regulate airflow through nozzle to achieve an air temperature
of 600° - 650°F at a point 7.62 (0.30) from the nozzle, (about 2.5 to 3 psig).
Apply heat until solder flow is noted.
7. Heat should be applied until solder melts and flows. The insulation sleeve will partially recover down
onto the wire insulation near the solder joint. The tops of the sleeves should not recover onto the wire
insulation as shown above.
Tyco Electronics Corporation
300 Constitutional Drive
Menlo Park, CA 94025 USA
TITLE:
SOLDERPAK ASSEMBLY,
BURNDY UPC CONNECTOR
?0.64x5.08 (?0.025x0.200) Terminals
with 2.54 (0.100) center spacing
UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS.
INCHES DIMENSIONS ARE BETWEEN BRACKETS.
DOCUMENT NO.:
D-711-04
TOLERANCES:
0.00 N/A
0.0 N/A
ANGLES: N/A
ROUGHNESS IN
Raychem reserves the right to amend this drawing
at any time. Users should evaluate the suitability
of the product for their application.
DATE:
18-July-00
DOC ISSUE:
1
0 N/A
MICRON
DRAWN BY:
M. FORONDA
CAGE CODE:
06090
REPLACES:
N/A
DCR NUMBER:
D000404
PROD. REV.:
B
SCALE:
None
SIZE:
A
SHEET:
2 of 2
If this document is printed it becomes uncontrolled. Check for the latest revision.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
626043-000 TERMINATOR SOLDER PAK WIRE
626050-000 SOLDER PAK WIRE TERMINATORS
626051-000 SOLDER PAK WIRE TERMINATORS
6269 REPLACE SCREWS #2-56 PAN HEAD
6278016-5 CABLE ASSY SC-SC DUPLEX MM 5M
6278153-1 MT-RJ LOOPBACK 62.5/125
6278357-1 MT-RJ LOOPBACK MM BARE
5SGXMA5N3F45I3LN FPGA - 现场可编程门阵列 FPGA - Stratix V GX 2304 LABS 840 IOs
相关代理商/技术参数
626-02500 制造商:HellermannTyton 功能描述:ADHESIVE, PVC, 250ML
626-02500 制造商:HellermannTyton 功能描述:ADHESIVE PVC 250ML
626025-1 制造商:TE Connectivity 功能描述:.250 FASTIN-ON REC. - Tape and Reel
626-025-262-012 功能描述:D-Sub标准连接器 25P RCPT RA .590 FP RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤:
626-025-262-013 功能描述:D-Sub标准连接器 25P RECPT RA .590 FP RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤:
626-025-262-032 功能描述:D-Sub标准连接器 D SUB RECEPTACLE RA .590 FP RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤:
626-025-262-033 功能描述:D-Sub标准连接器 D SUB RECEPTACLE RA .590 FP RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤:
626-025-662-043 功能描述:D-Sub标准连接器 D SUB RECEPTACLE RA .590 FP RoHS:否 制造商:Omron Electronics 位置/触点数量:9 排数:2 型式:Female 安装风格:Through Hole 安装角:Right 端接类型:Solder 过滤: